Lease/Rent

Waters BioAccord LC/MS System with ACQUITY Premier UPLC

Listing #:LS-007641
Brand:
Model:186018000, 186018002, 186018004, 186018006, BioAccord, RDa
Availability:In Stock
Condition:Refurbished
Warranty:90 Days
Onsite Installation:Available upon request
In Stock

Waters BioAccord LC/MS System with ACQUITY Premier UPLC — complete accurate-mass LC/MS pairing an inert ACQUITY Premier binary UPLC and TUV with the ACQUITY RDa TOF detector for intact mass, subunit, peptide mapping and oligonucleotide analysis. Refurbished and tested by Alliant Scientific.

Description

Waters BioAccord LC/MS System Overview

The Waters BioAccord LC/MS System with ACQUITY Premier UPLC is a complete, benchtop accurate-mass LC/MS for routine analysis of proteins, peptides, oligonucleotides and other biotherapeutics. It pairs the ACQUITY Premier binary UPLC with the ACQUITY RDa time-of-flight mass detector and a TUV detector, so every run delivers UV and accurate-mass data together. Waters designed the Waters BioAccord LC/MS for analysts who are not mass spectrometry specialists: guided setup, automated calibration and pre-programmed system checks on the RDa replace the manual tuning a research-grade TOF normally needs. The ACQUITY Premier front end adds MaxPeak High Performance Surfaces, which reduce analyte losses to metal surfaces in the flow path, a common problem with oligonucleotides, phosphorylated peptides and other metal-sensitive compounds.

How the System Works

The ACQUITY Premier Binary Solvent Manager mixes the gradient at up to 15,000 psi with a gradient delay volume of 90 µL or less, so fast gradients reach the column quickly. The Sample Manager FTN injects 0.1 to 10 µL through a flow-through needle from cooled plates or vials, and the CH-A column heater holds the column at temperature with active pre-heating of the mobile phase. After UV detection in the TUV, the eluent enters the ACQUITY RDa’s electrospray source through a ZSpray dual-orthogonal interface, and its high-stability time-of-flight analyzer measures the ions at a resolution above 10,000 FWHM. An integrated fluidics system on the RDa delivers calibration and lock mass solutions from on-board reservoirs, keeping mass accuracy within 2.5 ppm RMS across low and high mass acquisition modes.

This Waters BioAccord LC/MS System with ACQUITY Premier UPLC is offered refurbished, fully tested, in working condition by Alliant Scientific.

Includes:

  • Waters BioAccord LC/MS
    • ACQUITY RDa Detector (P/N 186010262)
  • Waters ACQUITY Premier UPLC
    • ACQUITY Premier Binary Solvent Manager (P/N 186018000)
    • ACQUITY Premier Sample Manager FTN (P/N 186018002)
    • ACQUITY Premier TUV Detector (P/N 186018006)
    • ACQUITY Premier Column Heater CH-A (P/N 186018004)
    • ACQUITY Premier solvent tray
  • Vacuum pump
  • PC with data system and monitor
  • 90-day warranty

Browse more refurbished LC/MS systems

Disclaimer: All brand names and trademarks are the property of their respective owners and are used for identification only. The seller is not authorized by or associated with Waters. Software, if included, is not transferable or upgradable.

Listing last updated: November 2026.

Waters BioAccord LC/MS System Specifications

Manufacturer Waters
Model BioAccord LC/MS System with ACQUITY Premier UPLC
Condition Refurbished
Mass Spectrometer
Analyzer Time-of-flight (TOF), ACQUITY RDa detector
Ion Source Electrospray (ESI), ZSpray dual-orthogonal interface
Resolution >10,000 FWHM
Mass Accuracy <2.5 ppm RMS (with lock mass)
Low Mass Range Up to m/z 2000 (positive and negative)
High Mass Range Up to m/z 7000 (positive), up to m/z 5000 (negative)
Scan Rate Up to 20 Hz
Calibration Automated, integrated fluidics with on-board reservoirs
ACQUITY Premier UPLC
Flow Path MaxPeak High Performance Surfaces (HPS)
Flow Range 0.001–2.000 mL/min
Max Pressure 15,000 psi up to 1.0 mL/min; 9,000 psi up to 2.0 mL/min
Gradient Delay Volume ≤90 µL (FTN configuration)
Solvents Up to 4 (A1/A2, B1/B2)
Injection Volume 0.1–10.0 µL (up to 1000 µL with optional extension loop)
Sample Formats 96/384-well plates, 48-position 2 mL vial plates, microcentrifuge tube plates
Sample Temperature 4.0–40.0 °C
Carryover ≤0.002% (caffeine, UV)
Column Heater CH-A, 20.0–90.0 °C, active pre-heating, columns up to 150 mm
UV Detector ACQUITY Premier TUV
System
Vacuum Pump Included
Data System PC with data system and monitor included
Warranty 90 days

Additional information

Availability

Brand

Condition

Model

, , , , ,

Onsite Installation

Warranty

Waters BioAccord LC/MS System Key Features

  • MaxPeak HPS inert flow path: reduces losses of oligonucleotides, phosphopeptides and metal-sensitive analytes.
  • >10,000 FWHM TOF resolution: accurate-mass data for proteins, peptides and small molecules.
  • <2.5 ppm mass accuracy: lock mass correction for confident mass confirmation.
  • High mass mode to m/z 7000: covers intact antibodies and subunits.
  • ≤90 µL gradient delay volume: fast gradients and short UPLC methods.
  • 15,000 psi binary UPLC: sub-2 µm column performance for sharp, narrow peaks.
  • ≤0.002% carryover: flow-through needle injection with cooled samples at 4–40 °C.
  • UV and MS in one run: TUV detection ahead of the mass spectrometer.
  • Guided setup and automated calibration: designed for analysts who are not MS specialists.

Waters BioAccord LC/MS System Applications

  • Biopharmaceutical development labs: intact mass and glycoform profiling of monoclonal antibodies.
  • Biologics QC labs: routine identity and subunit mass checks on antibody products, with UV and MS data together.
  • Peptide labs: peptide mapping of therapeutic proteins and accurate-mass confirmation of synthetic peptides.
  • Oligonucleotide developers: intact mass confirmation and purity analysis, helped by the inert MaxPeak HPS flow path.
  • Pharmaceutical analytical labs: impurity identification and forced degradation studies.
  • Natural products and lipid research labs: accurate-mass screening, library searching and lipid profiling.
  • Forensic labs: accurate-mass identification in seized drug analysis.

Waters BioAccord LC/MS System FAQ

Which LC comes with this BioAccord?
A Waters ACQUITY Premier binary UPLC with Sample Manager FTN, TUV detector and CH-A column heater.

What is MaxPeak HPS?
Waters’ inert High Performance Surfaces in the LC flow path, which reduce analyte losses to metal surfaces.

What resolution does the mass spectrometer provide?
Above 10,000 FWHM.

What is the mass accuracy?
Below 2.5 ppm RMS with lock mass correction.

What is the maximum LC pressure?
15,000 psi up to 1.0 mL/min.

Can it measure intact antibodies?
Yes. The high mass mode reaches m/z 7000 in positive ion mode.

What is included?
The BioAccord LC/MS, ACQUITY Premier UPLC modules, vacuum pump, PC with data system and monitor, and a 90-day warranty.